Hi. I have set for sale. 200€ +shipping. Couple of different sizes main jets included.
Check my sale post. viewtopic.php?f=5&t=376
Jones
Search found 148 matches
- 03 Jul 2020, 21:08
- Forum: Carbs, air & fuel
- Topic: I need a new set of carbs
- Replies: 7
- Views: 5914
- 16 Jun 2020, 22:42
- Forum: Ongoing Projects
- Topic: Jrkk's 1100 cafe build
- Replies: 129
- Views: 82226
Re: Jrkk's 1100 cafe build
I'm still middle of engine break in. Start was horrible. My carbs float needles wasn't holding, and I didn't noticed that, and I continue dilute my oil with gasoline. That's past now, but it still consume oil and piston crown is wet from oil. I have drive it hard from a start, but only 350km. Might ...
- 07 Jun 2020, 16:21
- Forum: Wanted
- Topic: 1100 swingarm wanted - NO NEED ANYMORE
- Replies: 2
- Views: 4529
Re: 1100 swingarm wanted - NO NEED ANYMORE
Thanks Ivor.
I found one cheap one, but if it's bad, I get back to you.
I found one cheap one, but if it's bad, I get back to you.
- 29 May 2020, 17:34
- Forum: The Zephyr Lounge
- Topic: Thanks for add
- Replies: 4
- Views: 3644
Re: Thanks for add
Hi Gerry. Glad that you are here also.
I'm trying to get those Yoshimura pistons that you tip, let's see how it goes.
-jones
I'm trying to get those Yoshimura pistons that you tip, let's see how it goes.
-jones
- 26 May 2020, 16:50
- Forum: Wanted
- Topic: 1100 swingarm wanted - NO NEED ANYMORE
- Replies: 2
- Views: 4529
1100 swingarm wanted - NO NEED ANYMORE
Offer your spare swing. All Models that fits 1100, interests me.
-Jones
EDIT. FOUND IT.
-Jones
EDIT. FOUND IT.
- 09 May 2020, 19:28
- Forum: Ongoing Projects
- Topic: Jrkk's 1100 cafe build
- Replies: 129
- Views: 82226
Re: Jrkk's 1100 cafe build
Thanks Eddie. Yes I bought cheap powder gun and owen. I was hoping that it would be easier to develop smooth surface, I've done better surface with rattlecans. This should be harder though. From time to time, I have lot's of parts to coat, so maybe it wasn't waste of money. Owen is near to ventilato...
- 08 May 2020, 22:58
- Forum: Ongoing Projects
- Topic: Jrkk's 1100 cafe build
- Replies: 129
- Views: 82226
Re: Jrkk's 1100 cafe build
I was going to sleep, when I remembered that I have lowered the tank, so decided to test that can I rise it back to original position, yes I can, and also maybe trim little bit of my steering stoppers. So my cad design was succes. 20200509_014654.jpg 20200509_014639.jpg I'm getting drunk and clock i...
- 08 May 2020, 22:28
- Forum: Ongoing Projects
- Topic: Jrkk's 1100 cafe build
- Replies: 129
- Views: 82226
Re: Jrkk's 1100 cafe build
One more.
This is good setup, if I ditch afr gauge some point, Speedo looks good in the middle.
Also replaced ignition wiring.
This is good setup, if I ditch afr gauge some point, Speedo looks good in the middle.
Also replaced ignition wiring.
- 08 May 2020, 22:21
- Forum: Ongoing Projects
- Topic: Jrkk's 1100 cafe build
- Replies: 129
- Views: 82226
Re: Jrkk's 1100 cafe build
Yes. I'm satisfied.
- 08 May 2020, 20:27
- Forum: Ongoing Projects
- Topic: Jrkk's 1100 cafe build
- Replies: 129
- Views: 82226
Re: Jrkk's 1100 cafe build
Thanks Silvercap. Today I finally powder coated top yoke. I made lot's of practice pieces, and there is always orange peel, no matter how I cure them in owen. And how much powder on. I decide that if it goes to hell, I sand and polish it, but I was forced to apply quite thick layer because of those ...